Trusted heat pump installation for Kimberly properties. Same-day service available, transparent pricing, and a workmanship guarantee.
Homeowners in Kimberly, Wisconsin upgrading to a modern heat pump gain dual-mode heating and cooling from a single system, and KIC Refrigeration ensures every installation is sized, configured, and commissioned to manufacturer standards. We evaluate your existing ductwork, electrical panel capacity, and insulation levels to recommend the right unit for your climate zone and structure.
Properties throughout Kimberly (pop. 7,622) face unique demands when it comes to heat pump installation. Wisconsin heating loads, cooling calculations, and the insulation levels and duct configurations found in Kimberly homes all influence the approach we take. KIC Refrigeration tailors every heat pump installation project to the conditions your property actually faces — no generic solutions.
Choosing the right contractor for heat pump installation in Kimberly, WI makes all the difference between efficient comfort and a system that short-cycles. KIC Refrigeration uses Manual J load calculations, installs to manufacturer specifications, and backs every project with a warranty. Call (866) 858-2961 to schedule your free assessment.
How our NATE-certified technicians deliver quality heat pump installation results from start to finish.
KIC Refrigeration sizes every heat pump installation in Kimberly, WI using Manual J load calculations — the ACCA industry standard. We factor in your home envelope, duct losses, infiltration rate, and the WI heating design temperature to select a system with the right capacity, SEER2 rating, and HSPF2 rating for your climate zone.
Based on the load calculation, we recommend heat pump models from top manufacturers that match your capacity requirements and efficiency goals. You receive a written proposal with equipment specs, SEER2 and HSPF2 ratings, estimated annual energy costs, and a fixed installation price.
At your Kimberly property, our installation team sets the outdoor unit on a level pad, mounts the air handler, runs and insulates new copper linesets, installs the condensate drain with a proper trap, wires the disconnect and thermostat, and commissions the system to factory specifications.
KIC Refrigeration commissions every heat pump installation in Kimberly, WI with a full performance verification. We document all commissioning readings, register your equipment warranty, explain maintenance schedules, and ensure you are completely comfortable operating your new system before we leave.
Get answers to the heat pump installation questions our customers ask most often.
Heat pump installation in Kimberly typically costs $5,000 to $12,000 for a standard split system including the outdoor condenser, indoor air handler or coil, new thermostat, refrigerant lineset, and all labor. High-efficiency variable-speed systems from Carrier, Trane, or Daikin with SEER2 ratings of 18 to 22 range from $10,000 to $18,000 installed. Ductless mini-split systems run $3,000 to $8,000 depending on the number of indoor zones. The total price depends on home size, system tonnage, efficiency tier, ductwork condition, and whether electrical upgrades are needed. KIC Refrigeration provides detailed proposals for Kimberly homeowners with all costs itemized and no hidden fees.
Yes. A heat pump provides both heating and cooling from a single outdoor unit by reversing the refrigerant cycle between seasons. Modern cold-climate heat pumps with variable-speed inverter compressors operate efficiently down to 0 to minus 15 degrees Fahrenheit. In extremely cold WI climates, a dual-fuel configuration pairs the heat pump with a gas furnace that engages as backup only below the economic balance point — the temperature where gas heating costs less per BTU than electric heat pump operation. This gives you heat pump efficiency for 80 to 90 percent of the season with gas backup for the coldest days. KIC Refrigeration designs the right configuration for your Kimberly climate zone and heating needs.
Many Kimberly homeowners qualify for substantial rebates and tax credits on heat pump installation. The federal energy-efficient home improvement credit covers up to $2,000 per year for qualifying heat pumps with SEER2 ratings above 16. State and utility rebates in WI may add $500 to $3,000 depending on the program and efficiency level. The Inflation Reduction Act provides additional point-of-sale rebates of up to $8,000 for qualifying heat pumps for income-eligible households. KIC Refrigeration tracks all available federal, state, and utility incentive programs in WI and helps Kimberly homeowners identify and apply for every rebate they qualify for during the proposal process.
The federal minimum efficiency for heat pumps is 15 SEER2 in the southern region and 14.3 SEER2 in the northern region as of January 2023. Systems rated 17 to 21 SEER2 deliver significantly lower monthly cooling costs and typically qualify for utility rebates in WI as well as the federal energy tax credit of up to $2,000 per year. The payback period for upgrading from a 15 to a 20 SEER2 system is typically 5 to 8 years in Kimberly depending on your usage and electricity rates. KIC Refrigeration calculates projected energy savings for each efficiency tier so you can make an informed decision based on real numbers rather than guesswork.
Hear from property owners who chose us for their heating and cooling needs.
"KIC Refrigeration has serviced our commercial HVAC system for two years now. Always professional, always on time. Would not trust anyone else."
"KIC Refrigeration installed a new furnace for us last winter. The team was respectful of our home, wore boot covers, and cleaned up everything. Top notch."
"AC tune-up before summer. Technician was early, finished in about forty-five minutes, and gave me a clean bill of health on the system. Easy process."